[Libav-user] Decoding single NALUs from x264 programmatically (no luck even with parser), works fine with concatenated NALUs

[Faraz Khan]

So the keyframe cannot be fed to the decoder one nal at a time? Is that
what you are suggesting?




On Mon, Jun 10, 2013 at 2:40 PM, Andy Shaules <bowljoman at gmail.com> wrote:

>  I always had to decode from the latest key frame up to the desired
> stream time nal,
>
>
> On 6/10/2013 2:36 PM, Faraz Khan wrote:
>
> Hi all,
> I'm trying to use ffmpeg as a decoder for a real-time x264 stream that I'm
> generating. It works fine if I try to decode entire frames, but if I try to
> decode a single NALU the decoder errors out saying 'no frame'. I've tried
> using the parser (av_parser_parse2) but the h264 decoder doesnt seem to
> like that output either. I'm using x264 with annex-b and repeat-headers on.
>
>  The encoder config is as follows:
>
> x264params.b_sliced_threads = 1;
> x264params.i_slice_max_size = 1350;
> x264params.i_width = yuvSize.width;
> x264params.i_height = yuvSize.height;
> x264params.i_fps_num = 10;
> x264params.i_fps_den = 1;
> x264params.b_vfr_input = 0;
> x264params.rc.i_bitrate = 1500;
>
>   // Intra refres:
> x264params.i_keyint_max = 50000000;
> x264params.b_intra_refresh = 1;
>
>  //Rate control:
>
> x264params.rc.i_rc_method = X264_RC_ABR;
> x264params.rc.i_vbv_buffer_size = 300;
> x264params.rc.i_vbv_max_bitrate = 1500;
>
>  //For streaming:
> x264params.b_repeat_headers = 1;
> x264params.b_annexb = 1;
>
>  x264_param_apply_profile(&x264params, "baseline");
>
>
>
>  I do the encode with:
>
>     int frame_size = x264_encoder_encode(x264Encoder, &nals, &i_nals, &
> pic_in, &pic_out);
>
>
>  Now, since the max slice size is 1350, each packet output is a udp
> packet of size < MTU (this is true) and sent across the network.
>
> I iterate over the nals[i].p_payload and send them over to the ffmpeg side
> for decoding. I receive the correct packet on the remote side.
>
> If I assemble ALL the NALUs that were output in this frame and feed it
> directly to the decoder (even without the parser), it works fine! If I feed
> one NALU at a time, it fails (event with the parse). I'm sending it to the
> parser like:
>
>
>  int plen = av_parser_parse2(codecParser, decoderContext, &outbuf,
> &outside, indata,inlength,0,0,0);
>
>
>  plen always reports that it consumed the entire NALU that I gave it -
> after consuming a few NALUs, the outsize and outbuf are set to some value.
> Feeding it into the decoder using:
>
>
>   int len = avcodec_decode_video2(decoderContext,decoderOutframe,
> &gotpic,&avpkt);
>
>
>  Results in it saying 'No frame'. Again, if avpkt.data contains the
> entire frame (all NALUs concatenated) it will work!
>
>
>  I'm obviously doing some obviously wrong - but I really cant figure out
> why it wont decode a single NALU. Or is this a limitation in ffmpeg?
>
>
>  Thanks Guys!
>
>
>
>
> --
> Faraz Khan
> Simple Collaboration Screensharing
> www.screenhero.com
>
>
> _______________________________________________
> Libav-user mailing listLibav-user at ffmpeg.orghttp://ffmpeg.org/mailman/listinfo/libav-user
>
>
>
> _______________________________________________
> Libav-user mailing list
> Libav-user at ffmpeg.org
> http://ffmpeg.org/mailman/listinfo/libav-user
>
>


-- 

--
Faraz Khan
Simple Collaboration Screensharing
www.screenhero.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://ffmpeg.org/pipermail/libav-user/attachments/20130610/cd79ad65/attachment.html>