|Version 3 (modified by evilsoup, 4 months ago) (diff)|
FFmpeg and AAC Encoding Guide
AAC, Advanced Audio Coding, is the successor format to MP3, and is defined in MPEG-4 part 3. It is often used within an MP4 container format, for music the .m4a extension is customarily used. The second-most common use is within matroska MKV files (used because it has better support for embedded text-based soft subtitles than MP4). The examples in this guide will use the extensions MP4 and M4A.
This is currently the highest-quality AAC encoder available with ffmpeg. Requires ffmpeg to be configured with --enable-libfdk_aac.
-afterburner 1 enables 'high-quality' mode. It doesn't add any noticeable length to the encoding time, or increase the filesize; so unless you have a specific reason not to, you should use it.
Variable Bit Rate (VBR) mode
These settings target a quality, rather than a specific bit rate. 1 is lowest quality (though still pretty good) and 5 is highest quality. For some people with some files, even a VBR of 1 is indistinguishable from CD-quality audio; test it out and use the lowest setting that works for you. This mode is not compatible with AAC-HE, but for AAC-LC (the default for ffmpeg, and most compatible AAC profile) it should probably be preferred, since it allows the encoder greater flexibility to distribute bits as it sees fit: high-tempo, large dynamic range audio (like dubstep or rock music) requires more bits to encode then low-tempo, low dynamic range audio (like whalesong, or a recorded lecture - though there are special speech codecs that you should consider for the latter). Set the VBR level with the -vbr:a flag.
According to this hydrogenaudio post, the VBR modes (on average, over a number of files) give the following bit rates per channel (so for stereo, double the bit rate; for 5.1 surround sound, multiply it by six):
Convert an audio file to AAC in an M4A (MP4) container:
ffmpeg -i input.wav -c:a libfdk_aac -vbr:a 3 -afterburner:a 1 output.m4a
Convert the audio only of a video:
ffmpeg -i input.mp4 -c:v copy -c:a libfdk_aac -vbr:a 3 -afterburner:a 1 output.mp4
Convert the video with libx264, and mix down audio to two channels:
ffmpeg -i input.mp4 -c:v libx264 -crf:v 22 -preset:v veryfast \ -ac 2 -c:a libfdk_aac -vbr:a 3 -afterburner:a 1 output.mp4
Constant Bit Rate (CBR) mode
These settings target a specific bit rate, with less variation between samples. It will get you slightly lower quality for the bit rate it gives than the VBR mode would; but it gives you greater control over filesize, and it is compatible with the HE-AAC profile. As a rule of thumb, for audible transparency, use 64kb/s for each channel (so 128kb/s for stereo, 384 kb/s for 5.1 surround sound). Set the bit rate with the -b:a flag.
Convert and audio file to AAC in an M4A (MP4) container:
ffmpeg -i input.wav -c:a libfdk_aac -b:a 128k -afterburner:a 1 output.m4a
Convert 5.1 surround sound audio of a video, leaving the video alone:
ffmpeg -i input.mp4 -c:v copy -c:a libfdk_aac -b:a 384k -afterburner:a 1 output.mp4
Convert the video with libx264, with a target of fitting a 90-minute movie on a 700MB(=5734400kb) CD-ROM, mixing the audio down to two channels (WIndows users should use NUL rather than /dev/null:
ffmpeg -y -i input.mp4 -c:v libx264 -b:v 933k -preset:v veryfast -pass 1 -an /dev/null && \ ffmpeg -i input.mp4 -c:v libx264 -b:v 933k -preset:v veryfast -pass 2 \ -ac 2 -c:a libfdk_aac -b:a 128k -afterburner:a 1 output.mp4
This is a pair of AAC profiles tailored for low bit rates (version 1 and version 2). AAC-HE version 1 is suited for bit rates below 64kb/s (for stereo audio) down to about 48 kb/s, while AAC-HE version 2 is suited for bit rates as low as 32 kb/s (again, for stereo).
Unfortunately, many devices that can play AAC-LC (the default profile for fdk_aac) simply cannot play either version of AAC-HE, so this is not recommended for surround sound audio, which normally needs to be compatible with such hardware players. If you are only going to play it on your computer, or you are sure that your hardware player supports AAC-HE, you can aim for a bit rate of 160kb/s for version 1, or 128kb/s for version 2. As always, experiment to see what works for your ears.
The following examples are taken from this ubuntuforum post.
AAC-HE version 1
ffmpeg -i input.wav -c:a libfdk_aac -profile:a aac_he -b:a 64k -afterburner:a 1 output.m4a
AAC-HE version 2
ffmpeg -i input.wav -c:a libfdk_aac -profile:a aac_he_v2 -b:a 32k -afterburner:a 1 output.m4a
If your version of ffmpeg isn't built with --enable-libfdk_aac, you can use ffmpeg's internal AAC encoder. Note that you will not get as good results as with fdk_aac.
ffmpeg -i input.wav -strict experimental -c:a aac -b:a 128k output.m4a