crystalhd.c

Go to the documentation of this file.

/*
 * - CrystalHD decoder module -
 *
 * Copyright(C) 2010,2011 Philip Langdale <ffmpeg.philipl@overt.org>
 *
 * This file is part of FFmpeg.
 *
 * FFmpeg is free software; you can redistribute it and/or
 * modify it under the terms of the GNU Lesser General Public
 * License as published by the Free Software Foundation; either
 * version 2.1 of the License, or (at your option) any later version.
 *
 * FFmpeg is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * Lesser General Public License for more details.
 *
 * You should have received a copy of the GNU Lesser General Public
 * License along with FFmpeg; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
 */

/*
 * - Principles of Operation -
 *
 * The CrystalHD decoder operates at the bitstream level - which is an even
 * higher level than the decoding hardware you typically see in modern GPUs.
 * This means it has a very simple interface, in principle. You feed demuxed
 * packets in one end and get decoded picture (fields/frames) out the other.
 *
 * Of course, nothing is ever that simple. Due, at the very least, to b-frame
 * dependencies in the supported formats, the hardware has a delay between
 * when a packet goes in, and when a picture comes out. Furthermore, this delay
 * is not just a function of time, but also one of the dependency on additional
 * frames being fed into the decoder to satisfy the b-frame dependencies.
 *
 * As such, a pipeline will build up that is roughly equivalent to the required
 * DPB for the file being played. If that was all it took, things would still
 * be simple - so, of course, it isn't.
 *
 * The hardware has a way of indicating that a picture is ready to be copied out,
 * but this is unreliable - and sometimes the attempt will still fail so, based
 * on testing, the code will wait until 3 pictures are ready before starting
 * to copy out - and this has the effect of extending the pipeline.
 *
 * Finally, while it is tempting to say that once the decoder starts outputting
 * frames, the software should never fail to return a frame from a decode(),
 * this is a hard assertion to make, because the stream may switch between
 * differently encoded content (number of b-frames, interlacing, etc) which
 * might require a longer pipeline than before. If that happened, you could
 * deadlock trying to retrieve a frame that can't be decoded without feeding
 * in additional packets.
 *
 * As such, the code will return in the event that a picture cannot be copied
 * out, leading to an increase in the length of the pipeline. This in turn,
 * means we have to be sensitive to the time it takes to decode a picture;
 * We do not want to give up just because the hardware needed a little more
 * time to prepare the picture! For this reason, there are delays included
 * in the decode() path that ensure that, under normal conditions, the hardware
 * will only fail to return a frame if it really needs additional packets to
 * complete the decoding.
 *
 * Finally, to be explicit, we do not want the pipeline to grow without bound
 * for two reasons: 1) The hardware can only buffer a finite number of packets,
 * and 2) The client application may not be able to cope with arbitrarily long
 * delays in the video path relative to the audio path. For example. MPlayer
 * can only handle a 20 picture delay (although this is arbitrary, and needs
 * to be extended to fully support the CrystalHD where the delay could be up
 * to 32 pictures - consider PAFF H.264 content with 16 b-frames).
 */

/*****************************************************************************
 * Includes
 ****************************************************************************/

#define _XOPEN_SOURCE 600
#include <inttypes.h>
#include <stdio.h>
#include <stdlib.h>

#include <libcrystalhd/bc_dts_types.h>
#include <libcrystalhd/bc_dts_defs.h>
#include <libcrystalhd/libcrystalhd_if.h>

#include "avcodec.h"
#include "h264.h"
#include "internal.h"
#include "libavutil/imgutils.h"
#include "libavutil/intreadwrite.h"
#include "libavutil/opt.h"

#if HAVE_UNISTD_H
#include <unistd.h>
#endif

/** Timeout parameter passed to DtsProcOutput() in us */
#define OUTPUT_PROC_TIMEOUT 50
/** Step between fake timestamps passed to hardware in units of 100ns */
#define TIMESTAMP_UNIT 100000
/** Initial value in us of the wait in decode() */
#define BASE_WAIT 10000
/** Increment in us to adjust wait in decode() */
#define WAIT_UNIT 1000


/*****************************************************************************
 * Module private data
 ****************************************************************************/

typedef enum {
    RET_ERROR           = -1,
    RET_OK              = 0,
    RET_COPY_AGAIN      = 1,
    RET_SKIP_NEXT_COPY  = 2,
    RET_COPY_NEXT_FIELD = 3,
} CopyRet;

typedef struct OpaqueList {
    struct OpaqueList *next;
    uint64_t fake_timestamp;
    uint64_t reordered_opaque;
    uint8_t pic_type;
} OpaqueList;

typedef struct {
    AVClass *av_class;
    AVCodecContext *avctx;
    AVFrame *pic;
    HANDLE dev;

    uint8_t *orig_extradata;
    uint32_t orig_extradata_size;

    AVBitStreamFilterContext *bsfc;
    AVCodecParserContext *parser;

    uint8_t is_70012;
    uint8_t *sps_pps_buf;
    uint32_t sps_pps_size;
    uint8_t is_nal;
    uint8_t output_ready;
    uint8_t need_second_field;
    uint8_t skip_next_output;
    uint64_t decode_wait;

    uint64_t last_picture;

    OpaqueList *head;
    OpaqueList *tail;

    /* Options */
    uint32_t sWidth;
    uint8_t bframe_bug;
} CHDContext;

static const AVOption options[] = {
    { "crystalhd_downscale_width",
      "Turn on downscaling to the specified width",
      offsetof(CHDContext, sWidth),
      AV_OPT_TYPE_INT, {.i64 = 0}, 0, UINT32_MAX,
      AV_OPT_FLAG_VIDEO_PARAM | AV_OPT_FLAG_DECODING_PARAM, },
    { NULL, },
};


/*****************************************************************************
 * Helper functions
 ****************************************************************************/

static inline BC_MEDIA_SUBTYPE id2subtype(CHDContext *priv, enum AVCodecID id)
{
    switch (id) {
    case AV_CODEC_ID_MPEG4:
        return BC_MSUBTYPE_DIVX;
    case AV_CODEC_ID_MSMPEG4V3:
        return BC_MSUBTYPE_DIVX311;
    case AV_CODEC_ID_MPEG2VIDEO:
        return BC_MSUBTYPE_MPEG2VIDEO;
    case AV_CODEC_ID_VC1:
        return BC_MSUBTYPE_VC1;
    case AV_CODEC_ID_WMV3:
        return BC_MSUBTYPE_WMV3;
    case AV_CODEC_ID_H264:
        return priv->is_nal ? BC_MSUBTYPE_AVC1 : BC_MSUBTYPE_H264;
    default:
        return BC_MSUBTYPE_INVALID;
    }
}

static inline void print_frame_info(CHDContext *priv, BC_DTS_PROC_OUT *output)
{
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tYBuffSz: %u\n", output->YbuffSz);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tYBuffDoneSz: %u\n",
           output->YBuffDoneSz);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tUVBuffDoneSz: %u\n",
           output->UVBuffDoneSz);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tTimestamp: %"PRIu64"\n",
           output->PicInfo.timeStamp);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tPicture Number: %u\n",
           output->PicInfo.picture_number);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tWidth: %u\n",
           output->PicInfo.width);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tHeight: %u\n",
           output->PicInfo.height);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tChroma: 0x%03x\n",
           output->PicInfo.chroma_format);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tPulldown: %u\n",
           output->PicInfo.pulldown);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tFlags: 0x%08x\n",
           output->PicInfo.flags);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tFrame Rate/Res: %u\n",
           output->PicInfo.frame_rate);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tAspect Ratio: %u\n",
           output->PicInfo.aspect_ratio);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tColor Primaries: %u\n",
           output->PicInfo.colour_primaries);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tMetaData: %u\n",
           output->PicInfo.picture_meta_payload);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tSession Number: %u\n",
           output->PicInfo.sess_num);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tycom: %u\n",
           output->PicInfo.ycom);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tCustom Aspect: %u\n",
           output->PicInfo.custom_aspect_ratio_width_height);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tFrames to Drop: %u\n",
           output->PicInfo.n_drop);
    av_log(priv->avctx, AV_LOG_VERBOSE, "\tH264 Valid Fields: 0x%08x\n",
           output->PicInfo.other.h264.valid);
}


/*****************************************************************************
 * OpaqueList functions
 ****************************************************************************/

static uint64_t opaque_list_push(CHDContext *priv, uint64_t reordered_opaque,
                                 uint8_t pic_type)
{
    OpaqueList *newNode = av_mallocz(sizeof (OpaqueList));
    if (!newNode) {
        av_log(priv->avctx, AV_LOG_ERROR,
               "Unable to allocate new node in OpaqueList.\n");
        return 0;
    }
    if (!priv->head) {
        newNode->fake_timestamp = TIMESTAMP_UNIT;
        priv->head              = newNode;
    } else {
        newNode->fake_timestamp = priv->tail->fake_timestamp + TIMESTAMP_UNIT;
        priv->tail->next        = newNode;
    }
    priv->tail = newNode;
    newNode->reordered_opaque = reordered_opaque;
    newNode->pic_type = pic_type;

    return newNode->fake_timestamp;
}

/*
 * The OpaqueList is built in decode order, while elements will be removed
 * in presentation order. If frames are reordered, this means we must be
 * able to remove elements that are not the first element.
 *
 * Returned node must be freed by caller.
 */
static OpaqueList *opaque_list_pop(CHDContext *priv, uint64_t fake_timestamp)
{
    OpaqueList *node = priv->head;

    if (!priv->head) {
        av_log(priv->avctx, AV_LOG_ERROR,
               "CrystalHD: Attempted to query non-existent timestamps.\n");
        return NULL;
    }

    /*
     * The first element is special-cased because we have to manipulate
     * the head pointer rather than the previous element in the list.
     */
    if (priv->head->fake_timestamp == fake_timestamp) {
        priv->head = node->next;

        if (!priv->head->next)
            priv->tail = priv->head;

        node->next = NULL;
        return node;
    }

    /*
     * The list is processed at arm's length so that we have the
     * previous element available to rewrite its next pointer.
     */
    while (node->next) {
        OpaqueList *current = node->next;
        if (current->fake_timestamp == fake_timestamp) {
            node->next = current->next;

            if (!node->next)
               priv->tail = node;

            current->next = NULL;
            return current;
        } else {
            node = current;
        }
    }

    av_log(priv->avctx, AV_LOG_VERBOSE,
           "CrystalHD: Couldn't match fake_timestamp.\n");
    return NULL;
}


/*****************************************************************************
 * Video decoder API function definitions
 ****************************************************************************/

static void flush(AVCodecContext *avctx)
{
    CHDContext *priv = avctx->priv_data;

    avctx->has_b_frames     = 0;
    priv->last_picture      = -1;
    priv->output_ready      = 0;
    priv->need_second_field = 0;
    priv->skip_next_output  = 0;
    priv->decode_wait       = BASE_WAIT;

    av_frame_unref (priv->pic);

    /* Flush mode 4 flushes all software and hardware buffers. */
    DtsFlushInput(priv->dev, 4);
}


static av_cold int uninit(AVCodecContext *avctx)
{
    CHDContext *priv = avctx->priv_data;
    HANDLE device;

    device = priv->dev;
    DtsStopDecoder(device);
    DtsCloseDecoder(device);
    DtsDeviceClose(device);

    /*
     * Restore original extradata, so that if the decoder is
     * reinitialised, the bitstream detection and filtering
     * will work as expected.
     */
    if (priv->orig_extradata) {
        av_free(avctx->extradata);
        avctx->extradata = priv->orig_extradata;
        avctx->extradata_size = priv->orig_extradata_size;
        priv->orig_extradata = NULL;
        priv->orig_extradata_size = 0;
    }

    av_parser_close(priv->parser);
    if (priv->bsfc) {
        av_bitstream_filter_close(priv->bsfc);
    }

    av_freep(&priv->sps_pps_buf);

    av_frame_free (&priv->pic);

    if (priv->head) {
       OpaqueList *node = priv->head;
       while (node) {
          OpaqueList *next = node->next;
          av_free(node);
          node = next;
       }
    }

    return 0;
}


static av_cold int init(AVCodecContext *avctx)
{
    CHDContext* priv;
    BC_STATUS ret;
    BC_INFO_CRYSTAL version;
    BC_INPUT_FORMAT format = {
        .FGTEnable   = FALSE,
        .Progressive = TRUE,
        .OptFlags    = 0x80000000 | vdecFrameRate59_94 | 0x40,
        .width       = avctx->width,
        .height      = avctx->height,
    };

    BC_MEDIA_SUBTYPE subtype;

    uint32_t mode = DTS_PLAYBACK_MODE |
                    DTS_LOAD_FILE_PLAY_FW |
                    DTS_SKIP_TX_CHK_CPB |
                    DTS_PLAYBACK_DROP_RPT_MODE |
                    DTS_SINGLE_THREADED_MODE |
                    DTS_DFLT_RESOLUTION(vdecRESOLUTION_1080p23_976);

    av_log(avctx, AV_LOG_VERBOSE, "CrystalHD Init for %s\n",
           avctx->codec->name);

    avctx->pix_fmt = AV_PIX_FMT_YUYV422;

    /* Initialize the library */
    priv               = avctx->priv_data;
    priv->avctx        = avctx;
    priv->is_nal       = avctx->extradata_size > 0 && *(avctx->extradata) == 1;
    priv->last_picture = -1;
    priv->decode_wait  = BASE_WAIT;
    priv->pic          = av_frame_alloc();

    subtype = id2subtype(priv, avctx->codec->id);
    switch (subtype) {
    case BC_MSUBTYPE_AVC1:
        {
            uint8_t *dummy_p;
            int dummy_int;

            /* Back up the extradata so it can be restored at close time. */
            priv->orig_extradata = av_malloc(avctx->extradata_size + FF_INPUT_BUFFER_PADDING_SIZE);
            if (!priv->orig_extradata) {
                av_log(avctx, AV_LOG_ERROR,
                       "Failed to allocate copy of extradata\n");
                return AVERROR(ENOMEM);
            }
            priv->orig_extradata_size = avctx->extradata_size;
            memcpy(priv->orig_extradata, avctx->extradata, avctx->extradata_size);

            priv->bsfc = av_bitstream_filter_init("h264_mp4toannexb");
            if (!priv->bsfc) {
                av_log(avctx, AV_LOG_ERROR,
                       "Cannot open the h264_mp4toannexb BSF!\n");
                return AVERROR_BSF_NOT_FOUND;
            }
            av_bitstream_filter_filter(priv->bsfc, avctx, NULL, &dummy_p,
                                       &dummy_int, NULL, 0, 0);
        }
        subtype = BC_MSUBTYPE_H264;
        // Fall-through
    case BC_MSUBTYPE_H264:
        format.startCodeSz = 4;
        // Fall-through
    case BC_MSUBTYPE_VC1:
    case BC_MSUBTYPE_WVC1:
    case BC_MSUBTYPE_WMV3:
    case BC_MSUBTYPE_WMVA:
    case BC_MSUBTYPE_MPEG2VIDEO:
    case BC_MSUBTYPE_DIVX:
    case BC_MSUBTYPE_DIVX311:
        format.pMetaData  = avctx->extradata;
        format.metaDataSz = avctx->extradata_size;
        break;
    default:
        av_log(avctx, AV_LOG_ERROR, "CrystalHD: Unknown codec name\n");
        return AVERROR(EINVAL);
    }
    format.mSubtype = subtype;

    if (priv->sWidth) {
        format.bEnableScaling = 1;
        format.ScalingParams.sWidth = priv->sWidth;
    }

    /* Get a decoder instance */
    av_log(avctx, AV_LOG_VERBOSE, "CrystalHD: starting up\n");
    // Initialize the Link and Decoder devices
    ret = DtsDeviceOpen(&priv->dev, mode);
    if (ret != BC_STS_SUCCESS) {
        av_log(avctx, AV_LOG_VERBOSE, "CrystalHD: DtsDeviceOpen failed\n");
        goto fail;
    }

    ret = DtsCrystalHDVersion(priv->dev, &version);
    if (ret != BC_STS_SUCCESS) {
        av_log(avctx, AV_LOG_VERBOSE,
               "CrystalHD: DtsCrystalHDVersion failed\n");
        goto fail;
    }
    priv->is_70012 = version.device == 0;

    if (priv->is_70012 &&
        (subtype == BC_MSUBTYPE_DIVX || subtype == BC_MSUBTYPE_DIVX311)) {
        av_log(avctx, AV_LOG_VERBOSE,
               "CrystalHD: BCM70012 doesn't support MPEG4-ASP/DivX/Xvid\n");
        goto fail;
    }

    ret = DtsSetInputFormat(priv->dev, &format);
    if (ret != BC_STS_SUCCESS) {
        av_log(avctx, AV_LOG_ERROR, "CrystalHD: SetInputFormat failed\n");
        goto fail;
    }

    ret = DtsOpenDecoder(priv->dev, BC_STREAM_TYPE_ES);
    if (ret != BC_STS_SUCCESS) {
        av_log(avctx, AV_LOG_ERROR, "CrystalHD: DtsOpenDecoder failed\n");
        goto fail;
    }

    ret = DtsSetColorSpace(priv->dev, OUTPUT_MODE422_YUY2);
    if (ret != BC_STS_SUCCESS) {
        av_log(avctx, AV_LOG_ERROR, "CrystalHD: DtsSetColorSpace failed\n");
        goto fail;
    }
    ret = DtsStartDecoder(priv->dev);
    if (ret != BC_STS_SUCCESS) {
        av_log(avctx, AV_LOG_ERROR, "CrystalHD: DtsStartDecoder failed\n");
        goto fail;
    }
    ret = DtsStartCapture(priv->dev);
    if (ret != BC_STS_SUCCESS) {
        av_log(avctx, AV_LOG_ERROR, "CrystalHD: DtsStartCapture failed\n");
        goto fail;
    }

    if (avctx->codec->id == AV_CODEC_ID_H264) {
        priv->parser = av_parser_init(avctx->codec->id);
        if (!priv->parser)
            av_log(avctx, AV_LOG_WARNING,
                   "Cannot open the h.264 parser! Interlaced h.264 content "
                   "will not be detected reliably.\n");
        priv->parser->flags = PARSER_FLAG_COMPLETE_FRAMES;
    }
    av_log(avctx, AV_LOG_VERBOSE, "CrystalHD: Init complete.\n");

    return 0;

 fail:
    uninit(avctx);
    return -1;
}


static inline CopyRet copy_frame(AVCodecContext *avctx,
                                 BC_DTS_PROC_OUT *output,
                                 void *data, int *got_frame)
{
    BC_STATUS ret;
    BC_DTS_STATUS decoder_status = { 0, };
    uint8_t trust_interlaced;
    uint8_t interlaced;

    CHDContext *priv = avctx->priv_data;
    int64_t pkt_pts  = AV_NOPTS_VALUE;
    uint8_t pic_type = 0;

    uint8_t bottom_field = (output->PicInfo.flags & VDEC_FLAG_BOTTOMFIELD) ==
                           VDEC_FLAG_BOTTOMFIELD;
    uint8_t bottom_first = !!(output->PicInfo.flags & VDEC_FLAG_BOTTOM_FIRST);

    int width    = output->PicInfo.width;
    int height   = output->PicInfo.height;
    int bwidth;
    uint8_t *src = output->Ybuff;
    int sStride;
    uint8_t *dst;
    int dStride;

    if (output->PicInfo.timeStamp != 0) {
        OpaqueList *node = opaque_list_pop(priv, output->PicInfo.timeStamp);
        if (node) {
            pkt_pts = node->reordered_opaque;
            pic_type = node->pic_type;
            av_free(node);
        } else {
            /*
             * We will encounter a situation where a timestamp cannot be
             * popped if a second field is being returned. In this case,
             * each field has the same timestamp and the first one will
             * cause it to be popped. To keep subsequent calculations
             * simple, pic_type should be set a FIELD value - doesn't
             * matter which, but I chose BOTTOM.
             */
            pic_type = PICT_BOTTOM_FIELD;
        }
        av_log(avctx, AV_LOG_VERBOSE, "output \"pts\": %"PRIu64"\n",
               output->PicInfo.timeStamp);
        av_log(avctx, AV_LOG_VERBOSE, "output picture type %d\n",
               pic_type);
    }

    ret = DtsGetDriverStatus(priv->dev, &decoder_status);
    if (ret != BC_STS_SUCCESS) {
        av_log(avctx, AV_LOG_ERROR,
               "CrystalHD: GetDriverStatus failed: %u\n", ret);
       return RET_ERROR;
    }

    /*
     * For most content, we can trust the interlaced flag returned
     * by the hardware, but sometimes we can't. These are the
     * conditions under which we can trust the flag:
     *
     * 1) It's not h.264 content
     * 2) The UNKNOWN_SRC flag is not set
     * 3) We know we're expecting a second field
     * 4) The hardware reports this picture and the next picture
     *    have the same picture number.
     *
     * Note that there can still be interlaced content that will
     * fail this check, if the hardware hasn't decoded the next
     * picture or if there is a corruption in the stream. (In either
     * case a 0 will be returned for the next picture number)
     */
    trust_interlaced = avctx->codec->id != AV_CODEC_ID_H264 ||
                       !(output->PicInfo.flags & VDEC_FLAG_UNKNOWN_SRC) ||
                       priv->need_second_field ||
                       (decoder_status.picNumFlags & ~0x40000000) ==
                       output->PicInfo.picture_number;

    /*
     * If we got a false negative for trust_interlaced on the first field,
     * we will realise our mistake here when we see that the picture number is that
     * of the previous picture. We cannot recover the frame and should discard the
     * second field to keep the correct number of output frames.
     */
    if (output->PicInfo.picture_number == priv->last_picture && !priv->need_second_field) {
        av_log(avctx, AV_LOG_WARNING,
               "Incorrectly guessed progressive frame. Discarding second field\n");
        /* Returning without providing a picture. */
        return RET_OK;
    }

    interlaced = (output->PicInfo.flags & VDEC_FLAG_INTERLACED_SRC) &&
                 trust_interlaced;

    if (!trust_interlaced && (decoder_status.picNumFlags & ~0x40000000) == 0) {
        av_log(avctx, AV_LOG_VERBOSE,
               "Next picture number unknown. Assuming progressive frame.\n");
    }

    av_log(avctx, AV_LOG_VERBOSE, "Interlaced state: %d | trust_interlaced %d\n",
           interlaced, trust_interlaced);

    if (priv->pic->data[0] && !priv->need_second_field)
        av_frame_unref(priv->pic);

    priv->need_second_field = interlaced && !priv->need_second_field;

    if (!priv->pic->data[0]) {
        if (ff_get_buffer(avctx, priv->pic, AV_GET_BUFFER_FLAG_REF) < 0)
            return RET_ERROR;
    }

    bwidth = av_image_get_linesize(avctx->pix_fmt, width, 0);
    if (priv->is_70012) {
        int pStride;

        if (width <= 720)
            pStride = 720;
        else if (width <= 1280)
            pStride = 1280;
        else pStride = 1920;
        sStride = av_image_get_linesize(avctx->pix_fmt, pStride, 0);
    } else {
        sStride = bwidth;
    }

    dStride = priv->pic->linesize[0];
    dst     = priv->pic->data[0];

    av_log(priv->avctx, AV_LOG_VERBOSE, "CrystalHD: Copying out frame\n");

    if (interlaced) {
        int dY = 0;
        int sY = 0;

        height /= 2;
        if (bottom_field) {
            av_log(priv->avctx, AV_LOG_VERBOSE, "Interlaced: bottom field\n");
            dY = 1;
        } else {
            av_log(priv->avctx, AV_LOG_VERBOSE, "Interlaced: top field\n");
            dY = 0;
        }

        for (sY = 0; sY < height; dY++, sY++) {
            memcpy(&(dst[dY * dStride]), &(src[sY * sStride]), bwidth);
            dY++;
        }
    } else {
        av_image_copy_plane(dst, dStride, src, sStride, bwidth, height);
    }

    priv->pic->interlaced_frame = interlaced;
    if (interlaced)
        priv->pic->top_field_first = !bottom_first;

    priv->pic->pkt_pts = pkt_pts;

    if (!priv->need_second_field) {
        *got_frame       = 1;
        if ((ret = av_frame_ref(data, priv->pic)) < 0) {
            return ret;
        }
    }

    /*
     * Two types of PAFF content have been observed. One form causes the
     * hardware to return a field pair and the other individual fields,
     * even though the input is always individual fields. We must skip
     * copying on the next decode() call to maintain pipeline length in
     * the first case.
     */
    if (!interlaced && (output->PicInfo.flags & VDEC_FLAG_UNKNOWN_SRC) &&
        (pic_type == PICT_TOP_FIELD || pic_type == PICT_BOTTOM_FIELD)) {
        av_log(priv->avctx, AV_LOG_VERBOSE, "Fieldpair from two packets.\n");
        return RET_SKIP_NEXT_COPY;
    }

    /*
     * The logic here is purely based on empirical testing with samples.
     * If we need a second field, it could come from a second input packet,
     * or it could come from the same field-pair input packet at the current
     * field. In the first case, we should return and wait for the next time
     * round to get the second field, while in the second case, we should
     * ask the decoder for it immediately.
     *
     * Testing has shown that we are dealing with the fieldpair -> two fields
     * case if the VDEC_FLAG_UNKNOWN_SRC is not set or if the input picture
     * type was PICT_FRAME (in this second case, the flag might still be set)
     */
    return priv->need_second_field &&
           (!(output->PicInfo.flags & VDEC_FLAG_UNKNOWN_SRC) ||
            pic_type == PICT_FRAME) ?
           RET_COPY_NEXT_FIELD : RET_OK;
}


static inline CopyRet receive_frame(AVCodecContext *avctx,
                                    void *data, int *got_frame)
{
    BC_STATUS ret;
    BC_DTS_PROC_OUT output = {
        .PicInfo.width  = avctx->width,
        .PicInfo.height = avctx->height,
    };
    CHDContext *priv = avctx->priv_data;
    HANDLE dev       = priv->dev;

    *got_frame = 0;

    // Request decoded data from the driver
    ret = DtsProcOutputNoCopy(dev, OUTPUT_PROC_TIMEOUT, &output);
    if (ret == BC_STS_FMT_CHANGE) {
        av_log(avctx, AV_LOG_VERBOSE, "CrystalHD: Initial format change\n");
        avctx->width  = output.PicInfo.width;
        avctx->height = output.PicInfo.height;
        switch ( output.PicInfo.aspect_ratio ) {
        case vdecAspectRatioSquare:
            avctx->sample_aspect_ratio = (AVRational) {  1,  1};
            break;
        case vdecAspectRatio12_11:
            avctx->sample_aspect_ratio = (AVRational) { 12, 11};
            break;
        case vdecAspectRatio10_11:
            avctx->sample_aspect_ratio = (AVRational) { 10, 11};
            break;
        case vdecAspectRatio16_11:
            avctx->sample_aspect_ratio = (AVRational) { 16, 11};
            break;
        case vdecAspectRatio40_33:
            avctx->sample_aspect_ratio = (AVRational) { 40, 33};
            break;
        case vdecAspectRatio24_11:
            avctx->sample_aspect_ratio = (AVRational) { 24, 11};
            break;
        case vdecAspectRatio20_11:
            avctx->sample_aspect_ratio = (AVRational) { 20, 11};
            break;
        case vdecAspectRatio32_11:
            avctx->sample_aspect_ratio = (AVRational) { 32, 11};
            break;
        case vdecAspectRatio80_33:
            avctx->sample_aspect_ratio = (AVRational) { 80, 33};
            break;
        case vdecAspectRatio18_11:
            avctx->sample_aspect_ratio = (AVRational) { 18, 11};
            break;
        case vdecAspectRatio15_11:
            avctx->sample_aspect_ratio = (AVRational) { 15, 11};
            break;
        case vdecAspectRatio64_33:
            avctx->sample_aspect_ratio = (AVRational) { 64, 33};
            break;
        case vdecAspectRatio160_99:
            avctx->sample_aspect_ratio = (AVRational) {160, 99};
            break;
        case vdecAspectRatio4_3:
            avctx->sample_aspect_ratio = (AVRational) {  4,  3};
            break;
        case vdecAspectRatio16_9:
            avctx->sample_aspect_ratio = (AVRational) { 16,  9};
            break;
        case vdecAspectRatio221_1:
            avctx->sample_aspect_ratio = (AVRational) {221,  1};
            break;
        }
        return RET_COPY_AGAIN;
    } else if (ret == BC_STS_SUCCESS) {
        int copy_ret = -1;
        if (output.PoutFlags & BC_POUT_FLAGS_PIB_VALID) {
            if (priv->last_picture == -1) {
                /*
                 * Init to one less, so that the incrementing code doesn't
                 * need to be special-cased.
                 */
                priv->last_picture = output.PicInfo.picture_number - 1;
            }

            if (avctx->codec->id == AV_CODEC_ID_MPEG4 &&
                output.PicInfo.timeStamp == 0 && priv->bframe_bug) {
                av_log(avctx, AV_LOG_VERBOSE,
                       "CrystalHD: Not returning packed frame twice.\n");
                priv->last_picture++;
                DtsReleaseOutputBuffs(dev, NULL, FALSE);
                return RET_COPY_AGAIN;
            }

            print_frame_info(priv, &output);

            if (priv->last_picture + 1 < output.PicInfo.picture_number) {
                av_log(avctx, AV_LOG_WARNING,
                       "CrystalHD: Picture Number discontinuity\n");
                /*
                 * Have we lost frames? If so, we need to shrink the
                 * pipeline length appropriately.
                 *
                 * XXX: I have no idea what the semantics of this situation
                 * are so I don't even know if we've lost frames or which
                 * ones.
                 *
                 * In any case, only warn the first time.
                 */
               priv->last_picture = output.PicInfo.picture_number - 1;
            }

            copy_ret = copy_frame(avctx, &output, data, got_frame);
            if (*got_frame > 0) {
                avctx->has_b_frames--;
                priv->last_picture++;
                av_log(avctx, AV_LOG_VERBOSE, "CrystalHD: Pipeline length: %u\n",
                       avctx->has_b_frames);
            }
        } else {
            /*
             * An invalid frame has been consumed.
             */
            av_log(avctx, AV_LOG_ERROR, "CrystalHD: ProcOutput succeeded with "
                                        "invalid PIB\n");
            avctx->has_b_frames--;
            copy_ret = RET_OK;
        }
        DtsReleaseOutputBuffs(dev, NULL, FALSE);

        return copy_ret;
    } else if (ret == BC_STS_BUSY) {
        return RET_COPY_AGAIN;
    } else {
        av_log(avctx, AV_LOG_ERROR, "CrystalHD: ProcOutput failed %d\n", ret);
        return RET_ERROR;
    }
}


static int decode(AVCodecContext *avctx, void *data, int *got_frame, AVPacket *avpkt)
{
    BC_STATUS ret;
    BC_DTS_STATUS decoder_status = { 0, };
    CopyRet rec_ret;
    CHDContext *priv   = avctx->priv_data;
    HANDLE dev         = priv->dev;
    uint8_t *in_data   = avpkt->data;
    int len            = avpkt->size;
    int free_data      = 0;
    uint8_t pic_type   = 0;

    av_log(avctx, AV_LOG_VERBOSE, "CrystalHD: decode_frame\n");

    if (avpkt->size == 7 && !priv->bframe_bug) {
        /*
         * The use of a drop frame triggers the bug
         */
        av_log(avctx, AV_LOG_INFO,
               "CrystalHD: Enabling work-around for packed b-frame bug\n");
        priv->bframe_bug = 1;
    } else if (avpkt->size == 8 && priv->bframe_bug) {
        /*
         * Delay frames don't trigger the bug
         */
        av_log(avctx, AV_LOG_INFO,
               "CrystalHD: Disabling work-around for packed b-frame bug\n");
        priv->bframe_bug = 0;
    }

    if (len) {
        int32_t tx_free = (int32_t)DtsTxFreeSize(dev);

        if (priv->parser) {
            int ret = 0;

            if (priv->bsfc) {
                ret = av_bitstream_filter_filter(priv->bsfc, avctx, NULL,
                                                 &in_data, &len,
                                                 avpkt->data, len, 0);
            }
            free_data = ret > 0;

            if (ret >= 0) {
                uint8_t *pout;
                int psize;
                int index;
                H264Context *h = priv->parser->priv_data;

                index = av_parser_parse2(priv->parser, avctx, &pout, &psize,
                                         in_data, len, avctx->internal->pkt->pts,
                                         avctx->internal->pkt->dts, 0);
                if (index < 0) {
                    av_log(avctx, AV_LOG_WARNING,
                           "CrystalHD: Failed to parse h.264 packet to "
                           "detect interlacing.\n");
                } else if (index != len) {
                    av_log(avctx, AV_LOG_WARNING,
                           "CrystalHD: Failed to parse h.264 packet "
                           "completely. Interlaced frames may be "
                           "incorrectly detected.\n");
                } else {
                    av_log(avctx, AV_LOG_VERBOSE,
                           "CrystalHD: parser picture type %d\n",
                           h->picture_structure);
                    pic_type = h->picture_structure;
                }
            } else {
                av_log(avctx, AV_LOG_WARNING,
                       "CrystalHD: mp4toannexb filter failed to filter "
                       "packet. Interlaced frames may be incorrectly "
                       "detected.\n");
            }
        }

        if (len < tx_free - 1024) {
            /*
             * Despite being notionally opaque, either libcrystalhd or
             * the hardware itself will mangle pts values that are too
             * small or too large. The docs claim it should be in units
             * of 100ns. Given that we're nominally dealing with a black
             * box on both sides, any transform we do has no guarantee of
             * avoiding mangling so we need to build a mapping to values
             * we know will not be mangled.
             */
            uint64_t pts = opaque_list_push(priv, avctx->internal->pkt->pts, pic_type);
            if (!pts) {
                if (free_data) {
                    av_freep(&in_data);
                }
                return AVERROR(ENOMEM);
            }
            av_log(priv->avctx, AV_LOG_VERBOSE,
                   "input \"pts\": %"PRIu64"\n", pts);
            ret = DtsProcInput(dev, in_data, len, pts, 0);
            if (free_data) {
                av_freep(&in_data);
            }
            if (ret == BC_STS_BUSY) {
                av_log(avctx, AV_LOG_WARNING,
                       "CrystalHD: ProcInput returned busy\n");
                usleep(BASE_WAIT);
                return AVERROR(EBUSY);
            } else if (ret != BC_STS_SUCCESS) {
                av_log(avctx, AV_LOG_ERROR,
                       "CrystalHD: ProcInput failed: %u\n", ret);
                return -1;
            }
            avctx->has_b_frames++;
        } else {
            av_log(avctx, AV_LOG_WARNING, "CrystalHD: Input buffer full\n");
            len = 0; // We didn't consume any bytes.
        }
    } else {
        av_log(avctx, AV_LOG_INFO, "CrystalHD: No more input data\n");
    }

    if (priv->skip_next_output) {
        av_log(avctx, AV_LOG_VERBOSE, "CrystalHD: Skipping next output.\n");
        priv->skip_next_output = 0;
        avctx->has_b_frames--;
        return len;
    }

    ret = DtsGetDriverStatus(dev, &decoder_status);
    if (ret != BC_STS_SUCCESS) {
        av_log(avctx, AV_LOG_ERROR, "CrystalHD: GetDriverStatus failed\n");
        return -1;
    }

    /*
     * No frames ready. Don't try to extract.
     *
     * Empirical testing shows that ReadyListCount can be a damn lie,
     * and ProcOut still fails when count > 0. The same testing showed
     * that two more iterations were needed before ProcOutput would
     * succeed.
     */
    if (priv->output_ready < 2) {
        if (decoder_status.ReadyListCount != 0)
            priv->output_ready++;
        usleep(BASE_WAIT);
        av_log(avctx, AV_LOG_INFO, "CrystalHD: Filling pipeline.\n");
        return len;
    } else if (decoder_status.ReadyListCount == 0) {
        /*
         * After the pipeline is established, if we encounter a lack of frames
         * that probably means we're not giving the hardware enough time to
         * decode them, so start increasing the wait time at the end of a
         * decode call.
         */
        usleep(BASE_WAIT);
        priv->decode_wait += WAIT_UNIT;
        av_log(avctx, AV_LOG_INFO, "CrystalHD: No frames ready. Returning\n");
        return len;
    }

    do {
        rec_ret = receive_frame(avctx, data, got_frame);
        if (rec_ret == RET_OK && *got_frame == 0) {
            /*
             * This case is for when the encoded fields are stored
             * separately and we get a separate avpkt for each one. To keep
             * the pipeline stable, we should return nothing and wait for
             * the next time round to grab the second field.
             * H.264 PAFF is an example of this.
             */
            av_log(avctx, AV_LOG_VERBOSE, "Returning after first field.\n");
            avctx->has_b_frames--;
        } else if (rec_ret == RET_COPY_NEXT_FIELD) {
            /*
             * This case is for when the encoded fields are stored in a
             * single avpkt but the hardware returns then separately. Unless
             * we grab the second field before returning, we'll slip another
             * frame in the pipeline and if that happens a lot, we're sunk.
             * So we have to get that second field now.
             * Interlaced mpeg2 and vc1 are examples of this.
             */
            av_log(avctx, AV_LOG_VERBOSE, "Trying to get second field.\n");
            while (1) {
                usleep(priv->decode_wait);
                ret = DtsGetDriverStatus(dev, &decoder_status);
                if (ret == BC_STS_SUCCESS &&
                    decoder_status.ReadyListCount > 0) {
                    rec_ret = receive_frame(avctx, data, got_frame);
                    if ((rec_ret == RET_OK && *got_frame > 0) ||
                        rec_ret == RET_ERROR)
                        break;
                }
            }
            av_log(avctx, AV_LOG_VERBOSE, "CrystalHD: Got second field.\n");
        } else if (rec_ret == RET_SKIP_NEXT_COPY) {
            /*
             * Two input packets got turned into a field pair. Gawd.
             */
            av_log(avctx, AV_LOG_VERBOSE,
                   "Don't output on next decode call.\n");
            priv->skip_next_output = 1;
        }
        /*
         * If rec_ret == RET_COPY_AGAIN, that means that either we just handled
         * a FMT_CHANGE event and need to go around again for the actual frame,
         * we got a busy status and need to try again, or we're dealing with
         * packed b-frames, where the hardware strangely returns the packed
         * p-frame twice. We choose to keep the second copy as it carries the
         * valid pts.
         */
    } while (rec_ret == RET_COPY_AGAIN);
    usleep(priv->decode_wait);
    return len;
}


#if CONFIG_H264_CRYSTALHD_DECODER
static AVClass h264_class = {
    "h264_crystalhd",
    av_default_item_name,
    options,
    LIBAVUTIL_VERSION_INT,
};

AVCodec ff_h264_crystalhd_decoder = {
    .name           = "h264_crystalhd",
    .long_name      = NULL_IF_CONFIG_SMALL("H.264 / AVC / MPEG-4 AVC / MPEG-4 part 10 (CrystalHD acceleration)"),
    .type           = AVMEDIA_TYPE_VIDEO,
    .id             = AV_CODEC_ID_H264,
    .priv_data_size = sizeof(CHDContext),
    .init           = init,
    .close          = uninit,
    .decode         = decode,
    .capabilities   = CODEC_CAP_DR1 | CODEC_CAP_DELAY,
    .flush          = flush,
    .pix_fmts       = (const enum AVPixelFormat[]){AV_PIX_FMT_YUYV422, AV_PIX_FMT_NONE},
    .priv_class     = &h264_class,
};
#endif

#if CONFIG_MPEG2_CRYSTALHD_DECODER
static AVClass mpeg2_class = {
    "mpeg2_crystalhd",
    av_default_item_name,
    options,
    LIBAVUTIL_VERSION_INT,
};

AVCodec ff_mpeg2_crystalhd_decoder = {
    .name           = "mpeg2_crystalhd",
    .long_name      = NULL_IF_CONFIG_SMALL("MPEG-2 Video (CrystalHD acceleration)"),
    .type           = AVMEDIA_TYPE_VIDEO,
    .id             = AV_CODEC_ID_MPEG2VIDEO,
    .priv_data_size = sizeof(CHDContext),
    .init           = init,
    .close          = uninit,
    .decode         = decode,
    .capabilities   = CODEC_CAP_DR1 | CODEC_CAP_DELAY,
    .flush          = flush,
    .pix_fmts       = (const enum AVPixelFormat[]){AV_PIX_FMT_YUYV422, AV_PIX_FMT_NONE},
    .priv_class     = &mpeg2_class,
};
#endif

#if CONFIG_MPEG4_CRYSTALHD_DECODER
static AVClass mpeg4_class = {
    "mpeg4_crystalhd",
    av_default_item_name,
    options,
    LIBAVUTIL_VERSION_INT,
};

AVCodec ff_mpeg4_crystalhd_decoder = {
    .name           = "mpeg4_crystalhd",
    .long_name      = NULL_IF_CONFIG_SMALL("MPEG-4 Part 2 (CrystalHD acceleration)"),
    .type           = AVMEDIA_TYPE_VIDEO,
    .id             = AV_CODEC_ID_MPEG4,
    .priv_data_size = sizeof(CHDContext),
    .init           = init,
    .close          = uninit,
    .decode         = decode,
    .capabilities   = CODEC_CAP_DR1 | CODEC_CAP_DELAY,
    .flush          = flush,
    .pix_fmts       = (const enum AVPixelFormat[]){AV_PIX_FMT_YUYV422, AV_PIX_FMT_NONE},
    .priv_class     = &mpeg4_class,
};
#endif

#if CONFIG_MSMPEG4_CRYSTALHD_DECODER
static AVClass msmpeg4_class = {
    "msmpeg4_crystalhd",
    av_default_item_name,
    options,
    LIBAVUTIL_VERSION_INT,
};

AVCodec ff_msmpeg4_crystalhd_decoder = {
    .name           = "msmpeg4_crystalhd",
    .long_name      = NULL_IF_CONFIG_SMALL("MPEG-4 Part 2 Microsoft variant version 3 (CrystalHD acceleration)"),
    .type           = AVMEDIA_TYPE_VIDEO,
    .id             = AV_CODEC_ID_MSMPEG4V3,
    .priv_data_size = sizeof(CHDContext),
    .init           = init,
    .close          = uninit,
    .decode         = decode,
    .capabilities   = CODEC_CAP_DR1 | CODEC_CAP_DELAY | CODEC_CAP_EXPERIMENTAL,
    .flush          = flush,
    .pix_fmts       = (const enum AVPixelFormat[]){AV_PIX_FMT_YUYV422, AV_PIX_FMT_NONE},
    .priv_class     = &msmpeg4_class,
};
#endif

#if CONFIG_VC1_CRYSTALHD_DECODER
static AVClass vc1_class = {
    "vc1_crystalhd",
    av_default_item_name,
    options,
    LIBAVUTIL_VERSION_INT,
};

AVCodec ff_vc1_crystalhd_decoder = {
    .name           = "vc1_crystalhd",
    .long_name      = NULL_IF_CONFIG_SMALL("SMPTE VC-1 (CrystalHD acceleration)"),
    .type           = AVMEDIA_TYPE_VIDEO,
    .id             = AV_CODEC_ID_VC1,
    .priv_data_size = sizeof(CHDContext),
    .init           = init,
    .close          = uninit,
    .decode         = decode,
    .capabilities   = CODEC_CAP_DR1 | CODEC_CAP_DELAY,
    .flush          = flush,
    .pix_fmts       = (const enum AVPixelFormat[]){AV_PIX_FMT_YUYV422, AV_PIX_FMT_NONE},
    .priv_class     = &vc1_class,
};
#endif

#if CONFIG_WMV3_CRYSTALHD_DECODER
static AVClass wmv3_class = {
    "wmv3_crystalhd",
    av_default_item_name,
    options,
    LIBAVUTIL_VERSION_INT,
};

AVCodec ff_wmv3_crystalhd_decoder = {
    .name           = "wmv3_crystalhd",
    .long_name      = NULL_IF_CONFIG_SMALL("Windows Media Video 9 (CrystalHD acceleration)"),
    .type           = AVMEDIA_TYPE_VIDEO,
    .id             = AV_CODEC_ID_WMV3,
    .priv_data_size = sizeof(CHDContext),
    .init           = init,
    .close          = uninit,
    .decode         = decode,
    .capabilities   = CODEC_CAP_DR1 | CODEC_CAP_DELAY,
    .flush          = flush,
    .pix_fmts       = (const enum AVPixelFormat[]){AV_PIX_FMT_YUYV422, AV_PIX_FMT_NONE},
    .priv_class     = &wmv3_class,
};
#endif